Shop
-
BBC Micro:Bit Complete Set (No Packaging)
$32.70Get creative, get connected & get coding with the BBC micro:bit go. A complete set containing all the parts and inspirational ideas to get started with the BBC micro:bit.
Each BBC micro:bit go contains 1x BBC micro:bit, USB cable, battery holder & 2x AAA batteries along with a Quick Start Guide featuring 4 fun ideas all in a retail ready pack. The BBC micro:bit go is the quickest and easiest way for children to get going with the BBC micro:bit.
The BBC micro:bit is a pocket-sized computer that you can code, customise and control to bring your digital ideas, games and apps to life. Measuring 4cm by 5cm, and designed to be fun and easy to use, users can create anything from games and animations to scrolling stories at school, at home and on the go – all you need is imagination and creativity. The BBC micro:bit is completely programmable. That means each of its LEDs can be individually programmed as can its buttons, inputs and outputs, accelerometer, magnetometer and Bluetooth
-
Breadboard Trim Potentiometer – 10K
$1.64Breadboard trim potentiometer – 10K
These potentiometers are great for project prototyping. The three legs are spaced to fit perfectly in our range of solderless breadboards, giving each leg its own lane for hooking up to your microcontroller with jumper wires.
-
DHT11 Temperature and Humidity Sensor
$5.45The DHT11 Temperature and Humidity Sensor is a low-cost and widely used sensor for measuring temperature and humidity in various applications. It is a combined digital temperature and humidity sensor that provides accurate and reliable data in a compact package. The DHT11 uses a capacitive humidity sensing element and a thermistor to measure the relative humidity and temperature, respectively. The sensor provides a digital output via a single wire interface, making it easy to connect to a microcontroller or other digital circuit. The DHT11 supports a temperature range of 0°C to 50°C and a humidity range of 20% to 90% relative humidity, making it suitable for use in a wide range of indoor and outdoor environments.
-
DHT22 Temperature and Humidity Sensor Module
$17.44DHT22 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). It’s fairly simple to use, but requires careful timing to grab data. The only real downside of this sensor is you can only get new data from it once every 2 seconds, so when using our library, sensor readings can be up to 2 seconds old.
-
ESP32-CAM IoT Kit
$49.05ESP32-CAM is an ESP32 Wireless IoT Vision Development Board in a very small form factor, designed to be used in various IoT projects, such as home smart devices, industrial wireless control, wireless monitoring, QR wireless identification and so on.
It supports deep sleep mode with power consumption as low as 6mA at 5V which makes it ideal for portable IoT applications. It’s suitable as a low-cost CCTV camera.
Package Included:
- 1 x ESP32-CAM Module
- 1 x Camera Module OV2640 2MP
- 1 x FT232RL Module
- 1 x Female to Female Dupont Jumper Wires
- 1 x 16GB microSD Card
-
ESP8266 ESP-12E Serial WIFI Module
$6.00ESP8266 ESP-12 Remote Serial Port WIFI Transceiver Wireless Module is developed by Ai-thinker Team. The module supports standard IEEE802.11 b/g/n, complete TCP/IP protocol stack. Users can use the
add modules to an existing device networking, or building a separate network controller. -
ESP8266 NodeMCU v2 WiFi Board
$21.80NodeMcu is an open-source firmware and development kit that helps you to prototype your IOT product within a few Lua script lines. The Development Kit based on ESP8266, integates GPIO, PWM, IIC, 1-Wire and ADC all in one board. Power your developement in the fastest way combining it with NodeMcu Firmware!
-
ESP8266 Serial WiFi Wireless Transceiver Module
$10.90ESP8266 Serial Wifi Wireless Transceiver Module is a low-cost, integrated Wi-Fi transceiver module designed for microcontroller projects. It operates on a single-chip SoC (System on Chip) and can be used to add Wi-Fi connectivity to microcontroller projects. The module can be connected to a microcontroller via serial communication, and it supports both station and soft access point modes, allowing it to connect to Wi-Fi networks or create its own network. The module can be programmed using the Arduino platform and has a small form factor, making it suitable for compact projects and wearable devices.
-
Ethernet Cable (1.5 meter)
$2.18- Exceed ANSI/TIA-568-D.2 Category 6 and ISO 11801 Class E Standards
- Up to 550MHz with 1G/10G-T Speed, Support PoE/PoE+/PoE++ (IEEE 802.3af/at/bt)
- Performance Tested with Fluke and Wired T568B
- Strain Relief and a Flexible Boot Simplify Moves, Additions and Changes
- Stranded Cable and RJ45 Modular Plugs with 50μ” Gold-plated Contacts
-
Use in Patch Panel or Equipment Connections in Enterprise Networks and Data CenterSupport Current and Future Category 6/5e/5 Applications
-
Female to Female 20cm 40P DuPont Color Jumper Wire
$4.36The Female to Female 20cm 40P DuPont Color Jumper Wire is a set of 40 wires that are commonly used in electronics projects and DIY circuits. These jumper wires feature a female connector on both ends and a 20cm length, making them suitable for use with a wide range of electronic components and printed circuit boards (PCBs).
The wires are made of high-quality materials and are designed to provide a secure and reliable connection between components. They are color-coded for easy identification and organization, allowing for quick and easy connections between components in a circuit.
-
Four-Channel Low Level Trigger Power 5V Relay Module
$10.90This four channels Relay Module can be used to control the lighting, electrical and other equipments through the digital IO port. The digital input circuit is optically isolated from the relay, so your controller is protected from voltage spikes and surges. The module is controlled with 5V signal and they are pre-soldered. A logic “LOW” to the control pin will turn the relay ON.
-
H-bridge Stepper Motor Dual DC Motor Driver Controller Board HG7881
$13.08The HG7881 H-Bridge Stepper Motor Dual DC Motor Driver Controller Board is a versatile motor control board designed to drive both stepper motors and DC motors. It uses an H-bridge configuration to control the direction and speed of the connected motors. The HG7881 is capable of driving motors that require up to 40 volts and 3 amps of current, making it suitable for a wide range of applications. It features a compact design, with a size of only 40 x 40 mm, and can be easily integrated into a variety of projects.
